ubuntu20固定串口名称

本文介绍: 把用户名加入了dialout用户组，因tty设备隶属于dialout用户组，重启系统。查看串口设备的id，id为1a86和7523。的10-local.rules文件中添加。（username为用户民），reboot重启最好。

查看串口的详细信息

udevadm info --name=/dev/ttyUSB0

结果：

P: /devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2/1-1.2:1.0/ttyUSB0/tty/ttyUSB0
N: ttyUSB0
L: 0
S: serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0
S: serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2:1.0-port0
S: device2
E: DEVPATH=/devices/platform/scb/fd500000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2/1-1.2:1.0/ttyUSB0/tty/ttyUSB0
E: DEVNAME=/dev/ttyUSB0
E: MAJOR=188
E: MINOR=0
E: SUBSYSTEM=tty
E: USEC_INITIALIZED=366284608
E: ID_BUS=usb
E: ID_VENDOR_ID=10c4
E: ID_MODEL_ID=ea60
E: ID_PCI_CLASS_FROM_DATABASE=Serial bus controller
E: ID_PCI_SUBCLASS_FROM_DATABASE=USB controller
E: ID_PCI_INTERFACE_FROM_DATABASE=XHCI
E: ID_VENDOR_FROM_DATABASE=Silicon Labs
E: ID_MODEL_FROM_DATABASE=CP210x UART Bridge
E: ID_VENDOR=Silicon_Labs
E: ID_VENDOR_ENC=Siliconx20Labs
E: ID_MODEL=CP2102_USB_to_UART_Bridge_Controller
E: ID_MODEL_ENC=CP2102x20USBx20tox20UARTx20Bridgex20Controller
E: ID_REVISION=0100
E: ID_SERIAL=Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001
E: ID_SERIAL_SHORT=0001
E: ID_TYPE=generic
E: ID_USB_INTERFACES=:ff0000:
E: ID_USB_INTERFACE_NUM=00
E: ID_USB_DRIVER=cp210x
E: ID_PATH=platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2:1.0
E: ID_PATH_TAG=platform-fd500000_pcie-pci-0000_01_00_0-usb-0_1_2_1_0
E: ID_MM_CANDIDATE=1
E: DEVLINKS=/dev/serial/by-id/usb-Silicon_Labs_CP2102_USB_to_UART_Bridge_Controller_0001-if00-port0 /dev/serial/by-path/platform-fd500000.pcie-pci-0000:01:00.0-usb-0:1.2:1.0-port0 /dev/device2
E: TAGS=:systemd:

通过id固定串口名称

通过lsusb查看串口设备的id，id为1a86和7523
在这里插入图片描述
在/etc/udev/rules.d的10-local.rules文件中添加

ACTION=="add", KERNEL=="ttyUSB*", ATTRS{idVendor}=="1a86", ATTRS{idProduct}=="7523", MODE:=“0777”，SYMLINK+="serialname"

保存关闭，重启服务sudo /etc/init.d/udev restart，reboot重启最好

通过USB口位置固定名称

还是借鉴一下本文
如果插入扩展坞扩展USB口，也能这么配置，比如把编号1-1.1的USB口扩展成4个USB口
重新配置rules文件，注释之前的1.1.1那行配置，再添加4行

# KERNEL=="ttyUSB*",KERNELS=="1-1.1",MODE:="0777",SYMLINK+="device1"
KERNEL=="ttyUSB*",KERNELS=="1-1.1.1",MODE:="0777",SYMLINK+="device11"
KERNEL=="ttyUSB*",KERNELS=="1-1.1.2",MODE:="0777",SYMLINK+="device12"
KERNEL=="ttyUSB*",KERNELS=="1-1.1.3",MODE:="0777",SYMLINK+="device13"
KERNEL=="ttyUSB*",KERNELS=="1-1.1.4",MODE:="0777",SYMLINK+="device14"